Freeway Medical - Design and Manufacturer of hospital trolleys, medical trolleys, medical furniture, medical equipment, custom design hospital equipment

01635 866717

Your Quote

Your quote is currently empty

Featured Product

Recently Viewed

FW7000-Resuscitation Room Divider

Specification

Dimensions:

Width: 3056mm

Height: 1900mm

Depth: 1050mm

Description:
Special features:

Freeway Room Divider Double sided approximately 2030(w) x 1050(d) x 1900(h)mm. White nylon modified polyester, complete with:-

 

- 4, 100mm high quality castors (2 Braked).

 

- Freeway Modular Room Divider Back Board System – Allowing the unit to be upgraded or repaired over the years at a drastically lower cost as each individual panel on the unit can be replaced individually with parts stocked for a minimum of 25 years. The result of this is vastly reduced life cycle costs as the units can be repaired at low cost easily with minimal fuss.  

 

- Divider Work shelf approximately 1960(w) x 500(d)mm. Including support brackets.

 

- Divider 5 drawer unit 650(w) x 475(d) x 680(h)mm. Complete with 5 drawer with internal dimensions of 545(w) x 435(d) x 125(h)mm. This unit would be mounted on the left hand side of the room divider.

 

- Divider Cupboard unit 650(w) x 435(d) x 680(h)mm. Complete with 1 removable shelf mounted on the right hand side of the room divider.

 

- Pull-out shelf - complete with handle, This would be mounted above the cupboard unit. This would be used as a work area when the shelf is pulled out, however it would not be able to hold any items when it is pushed back into the cabinet.

 

- Divider 5 drawer unit 650(w) x 475(d) x 680(h)mm. Complete with 5 drawer with internal dimensions of 545(w) x 435(d) x 125(h)mm. This unit would be mounted on the right hand side of the room divider.

 

 - Adjustable Triple Glove Box Holder, coated in white nylon modified polyester. This would be mounted on the right hand upright.

 

- Divider container storage brackets . Coated in white nylon modified polyester. Approximately 500 mm wide each. These would be mounted on the right hand side of the back board above the work surface.

 

- Large RED Plastic Container, this would be used in conjunction with part number FW7111.

 

- Easy Clean Airways cupboard with clear Polypropylene doors - This is mounted on the back board of the room divider, approximately 200mm deep with two clear sliding doors. Inside the airway cupboard is a Stainless Steel back board which has a series of custom designed holders to lay out the equipment need for either an adult or paediatric resuscitation event.

 

 

 

- Freeway Room Divider DOUBLE sided approximately 1026(w) x 1050(d) x 1900(h)mm. White nylon modified polyester, BOTH SIDES ARE IDENTICAL AND ARE MIRRORED IN THE FOLLOWING SPECIFICATION, complete with:-

 

- 4, 100mm castors (2 braked).

 

- Castors to be mounted on heavy duty plates to off set joining wheels.

 

- Freeway Modular Room Divider Back Board System – Allowing the unit to be upgraded or repaired over the years at a drastically lower cost as each individual panel on the unit can be replaced individually with parts stocked for a minimum of 25 years. The result of this is vastly reduced life cycle costs as the units can be repaired at low cost easily with minimal fuss.    

 

- Divider Work shelf approximately 1000(w) x 500(d)mm. Including support brackets.

 

- Divider 5 drawer unit 650(w) x 475(d) x 680(h)mm. Complete with 5 drawer with internal dimensions of 545(w) x 435(d) x 125(h)mm. This unit would be mounted on the left hand side of the room divider.

 

- Computer Cupboard unit 300(w) x 475(d) x 680(h)mm. Complete with Power and 2 x data connection – RJ45 IP rated “quick plug and play” fittings – Easy break away connections in the event of an emergency.

 

- CPU holding provision complete with Velcro straps, ventilated shelf.

 

- Can hold a UPS system if required, please advise of the specification when ordering.

 

- Cable Grommet to provide transition of Power / data and control cabling to the VDU / keyboard on the work surface

 

- Chart Holder to accommodate a variety of different chart sizes. Complete with 2 chart clips and pen holder facility. This would be fixed to the left hand side of the back board.

 

- Cable management to accommodate the 2 x RJ45 data cables and 1 x Power lead from the wall trunking under the unit via cable loops large enough to pass a mounded plug through under the main section of room divider cabinets.

 

- Three adjustable glove box holders, mounted on the right hand upright of the smaller room divider above the work surface. These would be mounted on a panel in their horizontal plane

 

- 1 x Apron roll dispenser, mounted on the right hand upright of the smaller room divider above the work surface. These would be mounted on a panel in their horizontal plane.

 

- 1 x Gel dispenser, mounted on the solid panel of the Apron roll dispenser.
Tags / Also Known As:
FW7000-Resuscitation Room Divider,,
Add to your quotation:

You have 0 x FW7000-Resuscitation Room Divider in your quote.

Continue Shopping
Proceed to Quote Form
Other products in the range:
FW9052